Shop Japan. We ship worldwide, bringing Japan directly to you.

I control the exciting current of hysteresis clutch brakes

Mitsubishi Electric LD-10PAU-A power amp NN

Mitsubishi Electric LD-10PAU-A power amp NN
  • Mitsubishi Electric LD-10PAU-A power amp NN
  • Mitsubishi Electric LD-10PAU-A power amp NN
  • Mitsubishi Electric LD-10PAU-A power amp NN
Buy it and earn 388 points! About Points
$ 345.13 (¥ 38,818)
Actual price may vary according to exchange rates.
Payment will be charged in yen
Please select options before adding to cart.
Shipping Options: Details
Payment Methods: Details
Credit Card

Product Information

Main specifications

Input/output specifications Power supply 24 V 24 to 29 V DC power consumption: 40 VA, inrush current: 30 A 1msec, Shun stop time 5 ms
24 G
Contact input REM Control output remote on/off (ON: output OFF/OFF: output ON) ON current: 5 mA
CUS Output cushion operation on/off (valid ON: off cushion /OFF cushion)
GAN Inertia compensation gains enabled
DIC Contact input common
PD 0-7 Parallel torque settings or external torque selection (4-bit significant)
Inertia compensation gain (top 4-bit) memory value Select
ON current: 5 mA
STB Parallel data Strobe
PDC Parallel data common
Contact output OCP Winding diameter detection for open collector output + 0.1 A (resistive load)
30 v
OCN Open collector output for detecting winding diameter-
Output + 5 V For volume 5 v ( 500-2 k Ω external resistor ) 10 mA MAX
Analog input SP1 Analog torque (tensile) settings 0-5 V, 0 to 10 V switch
250 Ω external resistor
4-20 mA available
SP2 "Analog inertia compensation gain settings-axis compensation gain settings and volume diameter input" from selection
SN Analog signal GND
Analog output MON Output monitor output 0 to 2 V, 0-5 V, 0 to 10 V switch load resistance 1 k Ω more
For the powder output PP DC24V series / brakes, hysteresis clutch/brake
PN DC24V0-1.0 A
Environmental specifications Ambient temperature -5 ~ +55 ° c
Ambient humidity 35 to 85% RH (no condensation)
Storage temperature range -25 to + 75 ° c
Vibration resistance Frequency Acceleration Single amplitude X, Y, Z directions 10 times
( total 80 minutes each )
DIN rail mounting 10-57 Hz - 0.035 mm
57-150 Hz 4.9 m / s 2 -
Direct mounting 10-57 Hz - 0.075 mm
57-150 Hz 9.8 m / s 2 -
Impact resistance 98 m / s 2 … 3-axis direction 3 times each
Power supply noise immunity According to the noise voltage 500 VP-p noise width 1 μ sec frequency of 30-100 Hz noise Simulator
Withstand voltage AC500V for 1 minute. Measured in bulk all terminals and earth ground, all terminals, except for grounding bulk and flat metal plates
Insulation resistance DC500V Megger by more than 5 M Ω... Measured in bulk all terminals and earth ground
Grounding D species ground ( 100 Ω below the electric system and common ground is non-)
Operating atmosphere Corrosive, flammable gases and conductive dust, dust is not terribly

Recently Viewed Products

See All >

Shipping Options



Payment Methods

Available Payment Methods

  • Credit Card


Credit Card

Credit Card We accept credit and debit cards.
The following credit and debit cards can be used:
•American Express

Return Policy

Any return or refund due to customers will not be accepted.

Not available for Overseas shipping

This product cannot be shipped to Us United States from the store.

Please contact the store for further information.


Delivery Rates : EMS (International Express Mail Service)

Ship to
Shipping Option
Note: Exchange rates are for reference only.
Back to Top